SAMPLE TRUCK WASH PRICING

THE FOLLOWING PRICES SHOW A TYPICAL TWO BAY, 100’ X 50’ TRUCK WASH FACILITY WITH IN A ONE DAY DRIVE AREA OF SASKATOON. THIS WILL PROVIDE BUDGET PRICING FOR THE SUPPLY AND INSTALL OF TWO TRUCK BAYS, WHICH IS USUALLY 4 PUMPS, 8 GUNS / WANDS. WATER HEATERS, SOFTENERS AND/OR SPOT FREE RINSE SYSTEM IS EXTRA. WE WILL REQUIRE DETAILED PLOT DRAWINGS TO PROVIDE A FORMAL QUOTATION FOR YOUR SPECIFIC REQUIREMENTS.

EQUIPMENT TO BE SUPPLIED AND SCOPE OF INSTALLATION, IS AS FOLLOWS;

• 4 – CAT MODEL 530 PUMPS, RATED 4.4 GPM @ 2500 PSI, C/W ADJUSTABLE, PRESSURE
  REGULATING UNLOADER VALVES, LIQUID FILLED GUAGES, BRASS BY-PASS AND
  AND INLET FITTINGS.
• 4 – 7.5 HORSEPOWER, 3 PHASE, TEFC, ELECTRIC MOTORS C/W BELTS AND PULLEYS.
  (specify voltage required)
• 1 – ALUMINUM FRAME ASSEMBLY C/W MOUNTING CHANNELS FOR PUMP/MOTORS
• 1 – 3 COMPARTMENT STAINLESS STEEL TANK ASSEMBLY C/W HYDROMINDERS FOR
  AUTOMATIC MIXING AND PROPORTIONING OF LIQUID SOAP AND WAX. RINSE
  PORTION OF TANK IS EQUIPPED WITH MECHANICAL FLOAT VALVE TO MAINTAIN
  SUFFICIENT WATER SUPPLY TO PUMPS AT ALL TIMES.
• 1 – MOTOR CONTROL PANEL C/W STARTERS, OVERLOAD PROTECTION, LOW VOLTAGE
  TRANSFORMER, INDICATOR LIGHTS AND IS PRE-WIRED TO MOTORS AND RELATED
  CONTROLS. PANEL IS CSA APPROVED.
• 4 – STAINLESS STEEL SOLENOID VALVES FOR SOAP.
• 4 – STAINLESS STEEL SOLENOID VALVES FOR WAX.
• 4 – REMOTE, PVC ENCLOSURES FOR ROTORY SWITCH AND DECAL.
• 8 – PLATED WAND HOLDERS C/W REPLACEABLE PVC INSERTS.
• 8 – TRIGGER GUN ASSEMBLIES C/W 36” INSULATED WANDS, S/S SPRAY TIP AND GUN
  SWIVELS.
• 8 – 25’ X 3/8 HOSE ASSEMLIES C/W ENDS AND GARDS.
• 4 – 100’ X ¼ GALVANIZED CABLE ASSEMBLY C/W EYELETS AND TURNBUCKLES FOR
  FESTOONING SYSTEM. ALSO INCLUDED ARE HOSE SLIDERS, AS REQUIRED.
• 1 – 4 BAY FOAM BRUSH PACKAGE C/W S/S SOLENOID VALVES, AIR OPERATED PUMP, AIR
  REGULATORS, NEEDLE VALVES, AND AIR WATER TRAP. BAY ITEMS INCLUDE 8 FOAM
  BRUSH HANDLES WITH BRUSH HEADS, MOUNTING HOOKS, AND HOSE AS REQUIRED.
  STAINLESS STEEL TANK AND HYDROMINDER INCLUDED. FOAM BRUSH SYSTEM
  INCLUDES A 3 WAY BALL VALVE TO CONTROL FOAM TO LEFT AND RIGHT SIDE OF
  EACH B AY.
• 1 – 4 BAY TIRE/ENGINE CLEANER/DEGREASER PACKAGE C/W S/S SOLENOID VALVES, AIR
  OPERATED CHEMICAL PUMP, AIR REGULATOR, HIGH PRESSURE “TEE” ASSEMBLY,
  STAINLESS STEEL TANK AND HYDROMINDER.
• 1 – 4 BAY, REMOTE START SYSTEM FOR TURNING BAY ON FROM OFFICE AREA, C/W
  INDICATOR LIGHTS, TOGGLE SWITCH, AND HOUR METERS.

  PACKAGE PRICE, INSTALLED. . . . . . . . . . $ 35,000.00

OPTIONAL EXTRA

• 4 – STAINLESS STEEL COIN METER AND ELECTRONIC TIMERS FOR LOONIES / TWOONIE
  OPERATION, C/W ROTORY SWITCH, INDICATOR LITE

  PRICE…………………………ADD……………$2,500.00

• 1 – 4 BAY WASHCARD SYSTEM C/W SALELITE SERVERS AND MAG STRIPE READERS AND/
  OR CREDIT CARD ACTIVATION. See washcard brochure…

INSTALLATION INCLUDED;

SUPPLY AND INSTALL ½” STAINLESS STEEL TUBING AND RELATED FITTINGS TO RUN FROM PUMP OUTLETS TO EACH BAY LOCATION.

SUPPLY AND INSTALLATION OF ¼ STAINLESS STEEL CABLE ASSY C/W SLIDER BRACKETS
TO PROVIDE FESTOONING OF HIGH PRESSURE LINES FROM CENTER OF EACH BAY TO
EACH END AND ON BOTH SIDES.

SUPPLY AND INSTALLATION OF LOW PRESSURE POLLY TUBE FOR FOAM BRUSH AND
TIRE/ENGINE CLEANER SYSTEMS.

SUPPLY AND INSTALLATION OF LOW VOLTAGE, PVC JACKETED CONTROL WIRE, TO
RUN FROM OUR CONTROL PANEL TO SWITCH IN WASH BAY AND CONTROLS IN OFFICE.

CUSTOMER INSTALLATION REQUIREMENTS;

WE WILL REQUIRE CONDUIT TO BE INSTALLED IN WASH BAY AREA TO RUN FROM SWITCH ENCLOSURE TO OUR MOTOR STARTER PANEL IN EQUIPMENT ROOM. THIS CAN
BE EITHER INSTALLED IN FLOOR, PRIOR TO CONCRETE, OR SURFACE MOUNTED. WE MAY ALSO BE ABLE TO INSTALL IN WALLS, WITH OUT CONDUIT IF BUILDING DESIGN ALLOWS.

A STURDY CONNECTION WILL BE REQUIRED ON EACH SIDE , AND AT THE FRONT, REAR
AND CENTRE OF EACH WASH BAY. THIS WILL ENABLE US TO ATTACH OUR FESTOONING
CALBE TO EACH SIDE OF EACH WASH BAY AND TIGHTEN WITH THE TURNBUCKLE. AN ACCURATE MEASUREMENT WILL BE NEEDED FOR THE LENGTH OF CABLE REQUIRED.

AN ELECTRICIAN WILL BE REQUIRED TO PROVIDE BREAKERS AND CONNECTIONS FROM
OUR MOTOR STARTER PANEL TO CUSTOMERS BREAKER PANEL.CONDUIT WILL ALSO BE REQUIRED FOR THE INSTALLATION OF THE OPTIONAL WASH CARD SYSTEM.

IT IS IMPORTANT TO PROVIDE SUFFICIENT BACKING AND MOUNTING AREAS FOR OUR
EQUIPMENT AS IT IS BEING INSTALLED INTO WASHBAYS. WE WILL COORDINATE WITH BUILDER, BUT PROVISIONS NEED TO BE CONSIDERED FOR MOUNTING OF SWITCHES, WAND HOLDERS, MAT CLAMPS, FOAM BRUSH HOOKS, ETC.

PANTHER WASH EQUIPMENT WILL NOT DO ON SITE MANUFACTURING OF BRACKETS OR BRACES TO ACCOMMODATE OUR INSTALLATION REQUIREMENTS.

COMPUTERS, PRINTERS AND OTHER PERIPHERAL ITEMS THAT MAY BE REQUIRED FOR THE WASH CARD SYSTEM ARE EXTRA.

TERMS

GST/PST EXTRA
FOB SITE.
2 – 4 WEEK DELIVERY FROM RECIEPT OF DEPOSIT
25 % DEPOSIT REQUIRED WITH ACCEPTED OFFER
65 % BALANCE DUE UPON COMPLETION OF INSTALLATION
10 % BALANCE DUE 30 DAYS FROM START UP

 

THANK YOU FOR THE OPPORTUNITY OF QUOTING, WE REMAIN,

YOURS TRULY,

KELLY WILKINSON